Bend wire beside fixed plier jaws and keep the elbow

Original, untested video brief. No input image or generated result is supplied.

1. Task and boundary

Hold one short piece of soft wire in fixed plier jaws and bend its free arm once. The useful distinction is where deformation occurs. The wire should form a compact elbow beside the jaw edge, while its gripped portion and most of the free arm remain straight. After the moving hand relaxes, the elbow remains instead of springing back to the starting line.

This original, untested brief uses a short, already gripped wire with ample empty space around its free end. It does not depict cutting, twisting several wires or measuring a precise angle. Treat the pliers as a fixed anchor and use the original hand to guide the free arm; moving the whole tool would make the local bend harder to inspect.

2. Authorized first frame

Prepare a photo or accurate drawing you own or are allowed to use. Show one plier head in a stable support, its jaws closed on the left part of a straight wire. The wire extends horizontally to the right. A hand already grips its far right end, leaving the first short section outside the jaw unobscured.

Choose a near-overhead view with a plain background, a visible jaw edge and room for the free arm to move downward in the image. A small original mark on the straight free arm helps distinguish rotation of that arm from sliding through the grip. Avoid very shiny wire that blends into the tool.

3. Use the generator

Open the current image-to-video generator in a mode accepting your authorized first frame. Paste the complete prompt, check the available settings and cost estimate, then submit only when ready. This page supplies text; it does not upload an image or start a generation.

4. Prompt and timing

Start from my authorized view of one straight soft wire held in fixed closed plier jaws, with the original hand on its far right end. Lock the camera, support and jaws. Keep the captured left segment stationary. Move the existing hand along a short downward arc, turning the free right arm around a compact bending region immediately outside the right jaw edge. Form one smooth local elbow there while the long free arm stays straight and the wire remains continuous with unchanged thickness. Keep the original free-arm mark attached to the same place. Do not let wire feed through the jaws or let the pliers turn with the hand. Stop after a modest bend. Ease the hand’s pull while retaining its light grip, and hold the new elbow instead of snapping straight. No cut, extra strand, helical coil, length growth, tool change, camera motion or angle annotation.

Opening: locate the gripping boundary and distinguish the fixed segment from the free arm.
Middle: follow the short region beside the jaw as the free arm changes direction without becoming a broad curve.
Ending: compare the retained elbow after the driving hand stops and eases its pull.

These beats are author suggestions, not exact model timing guarantees. Adapt their proportions to the clip length actually available.

5. Inspect the output

After inspecting your own output, record a time or frame, visible observation and pass, fail or inconclusive judgment for each condition. A convincing ending alone does not verify the preceding action.

The plier jaws and captured wire segment keep their original positions.
The bend forms next to the visible gripping edge, not halfway along the free arm.
The free arm stays mostly straight as its orientation changes.
The wire remains one continuous piece with no new strand or broken tip.
The original mark does not migrate toward or through the jaw.
The elbow remains during the ending hold; if the gripping edge is hidden, its localization is inconclusive.

6. Fix one failure

The whole wire rotates: anchor the captured segment and expose the jaw boundary.
A large curved arc replaces the free arm: reduce the motion and specify a compact elbow beside the jaw.
The wire slides through the tool: keep the original mark at the same distance along the free arm.
The elbow springs straight: request the retained shape after the hand stops, without claiming a material value.
A second wire appears: remove looping language and keep both original endpoints identifiable.

7. Ending and limits

Finish with one bent wire still held by the original jaws, a clear elbow beside the grip and a straight free arm at its new orientation.

Save your own generated result through the available result controls, together with the authorized input, exact prompt, settings and inspection notes.

No generated result, bending-force measurement or material test is supplied. A retained visible bend is a scene condition, not proof of alloy, ductility, fatigue life or a precise permanent angle.

The chain task changes angles between separate links. The snap-latch task requires a flexible arm to recover. Here one continuous wire changes shape locally and retains the elbow.