Pull one cork straight out and expose the original jar mouth

Original, untested video brief. No input image or generated result is supplied.

1. Task and boundary

Remove a simple push-in cork from an empty, upright jar. The visible task is the change from an inserted plug to a separate held object above an open mouth. Follow the cork’s lower edge as it emerges; a darker patch on top of the neck is not enough to establish removal. Keep the jar planted and preserve the same cork throughout.

Use a loose reusable stopper already protruding far enough to grip. This is an untested visual brief for straight extraction, with no thread, corkscrew, pressurized contents or sudden ejection. A small final gap is sufficient. The task does not establish the force required to remove a real closure or the condition of a seal.

2. Authorized first frame

Prepare a photograph or accurate drawing you own or may use. Show a small empty jar held stationary in a simple cradle, with a short plain cork inserted partway into its neck. The original hand already grips the exposed upper cork. Use a slightly elevated side view that shows both the front rim and the cork’s vertical side.

Leave clear headroom above the cork. Give it a small existing side spot so that turning, duplication and replacement are easier to notice. The jar neck should be transparent or outlined clearly enough to locate the inserted lower portion. Keep the fingers above the rim instead of wrapping over the whole neck.

3. Use the generator

Open the current image-to-video generator in a mode accepting your authorized first frame. Paste the complete prompt, check the available settings and cost estimate, then submit only when ready. This page supplies text; it does not upload an image or start a generation.

4. Prompt and timing

Start from my authorized image of one empty jar fixed in its cradle, one unthreaded cork partly inserted in the neck, and the original hand already holding the exposed cork. Lock the camera, cradle and jar. Pull the same cork slowly upward along the neck axis without twisting. Keep its side spot facing the same direction. Reveal progressively more of the original cork side as the inserted portion emerges. Continue until the lower tip visibly passes above the original rim and leaves a small open air gap. Keep the full cork attached to the original grip and keep the empty jar mouth visible below it. Stop the hand above the mouth and hold. Preserve the cork length, rim shape and jar position. Do not turn the stopper into a screw cap, stretch its bottom into the neck, pop it away, add liquid or conceal the clearance behind the fingers. No new hand, cut, camera movement or removal-force label.

Opening: locate the rim, inserted cork portion, original grip and side spot before motion.
Middle: follow the growing exposed cork side while the jar rim stays at its original height.
Ending: inspect a frame with the cork’s complete lower tip above the rim and visible air between the two.

These beats are author suggestions, not exact model timing guarantees. Adapt their proportions to the clip length actually available.

5. Inspect the output

After inspecting your own output, record a time or frame, visible observation and pass, fail or inconclusive judgment for each condition. A convincing ending alone does not verify the preceding action.

The jar and cradle remain fixed while the original hand rises.
The side spot stays attached and retains its facing direction.
The cork emerges continuously instead of appearing fully free in one jump.
Its lower tip clears the original rim before the final hold.
The separated cork retains its length and the mouth remains open below it.
If fingers or the front rim hide the clearance, record extraction as inconclusive.

6. Fix one failure

The cork screws upward: remove all twist or unscrew wording and retain the facing side spot.
The jar follows the hand: show the cradle clearly and constrain the jar base.
The cork stretches into a tail: shorten the requested travel and specify the original full lower tip.
An open mouth appears before the cork clears: inspect the rim crossing, not only the ending.
The grip blocks the gap: improve the first-frame viewing angle before changing the motion prompt.

7. Ending and limits

Finish with the intact cork held just above the same open jar, a visible gap beneath its tip and no change to the supporting cradle.

Save your own generated result through the available result controls, together with the authorized input, exact prompt, settings and inspection notes.

No generated take, measured pull force or closure test is supplied. Visible continuity can support a judgment about extraction, but cannot verify friction, seal quality or an unseen neck interior.

The threaded-cap task couples turning with a small rise. The connector task ends with insertion. This task keeps orientation fixed and requires the plug’s lower tip to clear the mouth completely.