Raise the wheelbarrow handles until both rear feet clear the ground

Original, untested video brief. No input image or generated result is supplied.

1. Task and boundary

Make a compact empty wheelbarrow tip forward slightly as its original handles rise. Both rear support feet leave the ground while the front wheel keeps contact. The useful change is the set of supporting contacts, not the height of the whole machine. A wheelbarrow floating upward with its wheel and feet together fails this task even if the handles end higher.

This is an original, untested visual brief for a simple single-wheel frame. It is not a lifting technique, load rating or balance calculation. Use an empty tray, a small handle movement and a flat unobstructed floor. Do not add walking, rolling over a step, tipping material out or a second lowering cycle.

2. Authorized first frame

Use your own or licensed photograph or accurate drawing. Show the complete side of one empty wheelbarrow with a slight rear angle so both rear feet are individually visible. Include one front wheel, its axle, the rigid tray-and-handle frame and the two original hands already holding the grips. If real identifiable people are used, obtain their consent to the animation.

Choose a floor seam under or beside the wheel and clear space below both rear feet. A small gap between the two feet in the image helps prevent one from hiding the other. Keep all frame joints credible in the input. A narrow pure side view that merges both feet cannot establish that both have lifted.

3. Use the generator

Open the current image-to-video generator in a mode accepting your authorized first frame. Paste the complete prompt, check the available settings and cost estimate, then submit only when ready. This page supplies text; it does not upload an image or start a generation.

4. Prompt and timing

Keep my original empty wheelbarrow and the background in one fixed view. Start with its front wheel and both rear feet on the floor. The two original hands raise the handles a small amount together. Let the rigid frame change angle around the supported front wheel and axle region, so both rear feet lift clear of the floor. Keep the wheel rim in contact with the same flat ground; allow a tiny natural wheel adjustment if needed, but no forward journey. The tray, handles and rear legs retain their original lengths and joints. Show visible air below each rear foot, then hold the raised-handle pose. Do not lift the entire wheelbarrow off the floor, stretch its legs, retract the feet into the tray or add a second wheel. Do not move the floor seam, add a load, spill material, change the camera or lower the handles again.

Opening: identify the wheel-ground contact and the two separate rear-foot contacts.
Middle: follow the original handles upward while the rigid frame changes angle and both rear gaps appear.
Ending: hold the clear rear-foot gaps while checking that the same front wheel still meets the floor.

These beats are author suggestions, not exact model timing guarantees. Adapt their proportions to the clip length actually available.

5. Inspect the output

After inspecting your own output, record a time or frame, visible observation and pass, fail or inconclusive judgment for each condition. A convincing ending alone does not verify the preceding action.

The original wheel is in ground contact before and after the support change.
Both rear feet begin on the floor and each develops a visible gap.
The rear feet remain attached to the original rigid frame rather than retracting or shrinking.
The handles rise together without a twist that leaves only one foot supported.
No floor translation or camera rise substitutes for the contact change.
If either rear foot or the wheel contact is hidden during the transition, mark that support check inconclusive.

6. Fix one failure

The whole object floats upward: anchor the wheel to a visible floor reference and reduce handle lift.
Only the nearer foot clears: use a slight rear angle and keep both grips at matched heights.
The legs shrink: preserve their rigid lengths and move the frame as one connected assembly.
The wheel rolls away: remove walking language and request only a short stationary tip.
A hand lets go: begin with both grips visible and keep the action smaller.

7. Ending and limits

End with both rear feet clear, the handles raised and the same front wheel supported by the floor. Keep the original empty tray intact and quiet.

Save your own generated result through the available result controls, together with the authorized input, exact prompt, settings and inspection notes.

No physical lift or generated result has been performed. The contact observations do not measure weight transfer, gripping force, load capacity or stability outside the depicted pose. A hidden ground contact cannot be certified from the tray angle alone.

The rocking-tile exercise alternates contact under a rigid object before it settles flat. Here two identified feet lose support while one identified wheel retains it; the final state stays raised and the handles participate in holding that state.