Turn one pancake over and land with its opposite face upward

Original, untested video brief. No input image or generated result is supplied.

1. Task and boundary

Flip one small pancake in a stationary pan with one spatula. The disc starts supported, rises with the blade, turns through an edge-on view and returns with the opposite face upward. Preserve its rim and a small asymmetric edge feature throughout. Changing the top pattern in place is not a flip. Nor does a pancake that rises and returns with its original top still visible satisfy the ending.

This original, untested brief isolates a short turnover, not a cooking process. Use an empty unheated pan in the visual setup; omit flames, steam, pouring batter and browning changes. A brief separation from the spatula during the turn may be visible. Do not demand a physically impossible permanent attachment of the pancake to the blade throughout a full turnover.

2. Authorized first frame

Prepare a photograph or accurate drawing you own or may use. Show one small cooked pancake with a recognizable uneven rim on a plain pan. One broad spatula already slides beneath most of it, held by the original hand. The initial upper face has two existing brown spots; a slightly raised edge exposes a small part of the paler lower face.

Use an elevated side view with enough space above the pan for a low flip. Keep the handle, pan rim and landing area visible. The pancake should fit comfortably on the blade so the initial lift is readable. Avoid a very tall toss, a second pancake or a top-down view that hides the edge-on phase.

3. Use the generator

Open the current image-to-video generator in a mode accepting your authorized first frame. Paste the complete prompt, check the available settings and cost estimate, then submit only when ready. This page supplies text; it does not upload an image or start a generation.

4. Prompt and timing

Start with my authorized image of one marked pancake in one fixed pan, with the original spatula beneath it and the original hand on the handle. Lock the camera and pan. Lift the same pancake slightly with the supporting spatula, then turn it over in one low controlled motion. Follow its uneven rim through a continuous edge-on orientation. Let the original spotted upper face rotate downward and the original paler lower face rotate upward. A short visible gap from the blade during this turn is allowed; preserve one disc and its edge identity through that gap. Let the pancake return to the original pan with the formerly lower face on top. It settles on the pan once, with only a small soft rim movement. Withdraw the spatula to the side and hold the ending. Do not replace the disc at the edge-on moment, paint a new top pattern without rotation, flip twice, split the pancake or keep it floating. No heat effects, new food, cut, extra hand or camera move.

Opening: locate the original upper-face spots, uneven rim and spatula support before lift.
Middle: follow the rim and the face change through the edge-on moment; do not skip this part when checking the clip.
Ending: inspect the opposite face upward after contact with the pan and after the spatula moves clear.

These beats are author suggestions, not exact model timing guarantees. Adapt their proportions to the clip length actually available.

5. Inspect the output

After inspecting your own output, record a time or frame, visible observation and pass, fail or inconclusive judgment for each condition. A convincing ending alone does not verify the preceding action.

The same single disc lifts from the original pan without leaving a duplicate.
The initial lift visibly follows the supporting spatula rather than beginning before contact.
A continuous edge-on phase connects the two face orientations.
The original upper-face spots turn downward instead of dissolving on a flat stationary disc.
The opposite face ends upward and the pancake rests on the same pan after one landing.
If the edge-on moment is hidden behind the blade, mark the turnover identity inconclusive.

6. Fix one failure

Only the texture changes: retain a distinctive rim feature and require its continuous turn.
The pancake rises without turning: give the edge-on phase its own visible middle beat.
The disc sticks to the spatula in an impossible full orbit: allow a brief free gap during turnover.
Two pancakes overlap during landing: start with one clear silhouette and avoid motion-blur language.
The pancake flips back again: stop after the first opposite-face landing and withdraw the blade.

7. Ending and limits

End with the same pancake resting in the stationary pan, its formerly lower face upward and the spatula clear of the final contact region.

Save your own generated result through the available result controls, together with the authorized input, exact prompt, settings and inspection notes.

No generated take, cooking result or measured trajectory is supplied. The visible sequence can support a judgment about orientation and one landing, but cannot establish cooking quality, temperature, exact force or motion hidden behind the utensil.

The fruit-slice landing task follows one object into contact with a plate. This task additionally requires a continuous half-turn that exchanges the visible faces before the same soft disc returns to support.