Cut one end slice and show the gap after the knife withdraws

Original, untested video brief. No input image or generated result is supplied.

1. Task and boundary

Separate a narrow end slice from a small soft loaf in one continuous view. The blade enters the top, travels through the original thickness and reaches the board. After it withdraws, the new slice rests slightly apart from the remainder. The central question is whether one cutting path created one separation. A dark line on the loaf or a second piece that appears beside it is insufficient evidence.

This original, untested brief isolates a visible single-blade action. It does not supply cooking instructions, a material test or a claim about knife performance. Use an already positioned blade and a stable small loaf; omit sawing cycles, decorative garnish, crumbs bursting toward the camera and repeated slices. The board must remain visible at the end of the cutting path.

2. Authorized first frame

Use a photograph or accurate illustration that you own or may use. Show one unbranded soft loaf resting on a plain board, with a narrow proposed slice at its near end. The original hand holds one knife above that cut line. Choose a three-quarter side view that exposes the loaf top, near side and blade’s lower approach to the board.

An existing small crust mark on the future slice helps preserve identity. Keep it separate from any mark on the remaining loaf. Leave a little empty board beside the slice for the final gap. The knife should not hide the entire end piece throughout the shot. Do not start with a pre-existing gap and later pretend that the stroke created it.

3. Use the generator

Open the current image-to-video generator in a mode accepting your authorized first frame. Paste the complete prompt, check the available settings and cost estimate, then submit only when ready. This page supplies text; it does not upload an image or start a generation.

4. Prompt and timing

Begin with my authorized image of one intact soft loaf on a fixed board and one knife held by the original hand above a narrow end-slice line. Keep the camera, board and remaining loaf still. Lower the same blade through that line in one slow cutting stroke with a small continuous forward draw. Let the visible edge advance from the top through the original loaf thickness until it reaches the board plane. Keep the far portion connected until the edge passes it; do not reveal a detached slice ahead of the blade. Withdraw the knife along the cut and let its final outward movement ease the new end slice slightly away. Leave that single slice resting on the same board with a narrow visible gap after the blade is clear. Preserve its original crust mark and the remaining loaf face. Do not cut the board, create several parallel slices, grow an extra knife, turn the blade into scissors or substitute a new piece. No cutaway edit, airborne toss, extra hand or camera move.

1. Opening: locate the intact loaf, proposed cut line, original blade and small mark belonging to the end slice.
2. Middle: inspect the blade’s progress through the height of the loaf and its arrival at the original board plane.
3. Ending: wait until the blade has withdrawn, then compare the two exposed faces and the empty gap above the board.

These beats are author suggestions, not exact model timing guarantees. Adapt their proportions to the clip length actually available.

5. Inspect the output

After inspecting your own output, record a time or frame, visible observation and pass, fail or inconclusive judgment for each condition. A convincing ending alone does not verify the preceding action.

• There is one blade throughout the action, and exactly one newly separated end slice by the end.
• The blade advances through the original material before the separation opens.
• The remaining loaf and board keep their initial positions.
• The edge reaches the board plane without passing down through the board.
• The final slice retains its identifying mark and rests on the original board.
• If the blade or loaf blocks the last connected region, mark complete cutting as inconclusive even if the ending looks separated.

6. Fix one failure

• The slice appears before contact: show the intact end clearly in the first frame and slow the initial stroke.
• Only a painted line changes: require the edge to traverse the visible side thickness before withdrawal.
• Several slices appear: shorten the shot and specify one end piece with one identity mark.
• The knife sinks through the board: keep the board plane visible and stop downward travel there.
• A gap exists only while the knife occupies it: hold the ending after the blade is fully clear.

7. Ending and limits

End with one marked slice resting a small distance from the unchanged remainder, both supported by the same board and no blade filling their gap.

Save your own generated result through the available result controls, together with the authorized input, exact prompt, settings and inspection notes.

No generated take or cutting trial is supplied. The visible sequence can support a judgment about one depicted separation. It cannot establish sharpness, cutting force, food condition or continuity hidden behind the blade.

The scissor task closes two blades across a narrow paper strip. Here one blade traverses a soft block’s thickness, withdraws, and leaves a supported end slice with a visible gap.